If you are replacing the outdated drinking water heater with a new unit that is similar to the outdated 1, you will not discover it very challenging to change it. Additionally, if you adhere to the measures beneath, it will undoubtedly make your process much simpler.
- Shut off the drinking water supply
- If you have a gasoline tank, shut off the gasoline supply, or if you have an electric tank, flip off the power supply.
- The following step is to drain the h2o from the aquarium. If you do not have a floor drain beneath the valve, you can join a hose to the drain valve, close the foundation of the aquarium. Run it to a nearby drain or outdoors, and then open the valve.
- Unscrew the inlt and outlet fittings from the leading of the tank, using two wrenches.
- If you have a fuel drinking water heater, turn away the fuel inlt valve. Disconnect the union or flare fitting between the fuel offer pipe and the inlt valve. You can use two wrenches to disconnect the exact same. You will also discover a flue hat at the leading of the tank. It expels gases into the flue. Get rid of this flue hat as properly.
- Eliminate the previous h2o heater tank.
- Set the new h2o heater tank cautiously in spot so that the burner and controls are accessible. Make certain that there is at least six inches of clearance approximately its perimeter, and it is away from any flammable supplies.
- It is better if you fill the base with pieces of asphalt shingles or plastic wedges.
- Wrap the threads of the warmth entice fittings with pipe-wrap tape.
- Connect blue thread of the fittings into the chilly h2o inlt of the h2o heater tank, and red into the sizzling h2o outlet.
- Be careful while connecting the exact same. Make positive that the arrows are marked on the fittings level in the drinking water movement direction.
- On the inlt and outlet pipes of drinking water tank install the new versatile connectors.
- Make positive that all connections are complete.
- Open the shutoff wall and fill the fish tank.
- Open a couple of sizzling-h2o faucets so that the air in the pipes ought to bleed away.
- Now assemble the fuel pipes per the manufacturer's instruction.
- Brush soapy h2o on all the connections, and cautiously view it ought to not create any bubbles. If it does, recheck the connection as soon as once again.
Some Other Helpful Suggestions
- Check with your local constructing department and verify regardless of whether your house is in an earthquake zone. Set up straps approximately the new drinking water tank.
- If the peak of the new tank is distinct from the outdated 1, you will have to use versatile pipe connectors for the drinking water inlt and outlet. This will make them in a position to bend whenever it is required to make the hookup.
In case the pipes are not threaded, change them with threaded nipples. Use an adjustable wrench to modify the connectors to the nipples.
Therefore, if you adhere to the over measures and the tips, you will discover it very easy to change a drinking water heater.
- Shut off the drinking water supply
- If you have a gasoline tank, shut off the gasoline supply, or if you have an electric tank, flip off the power supply.
- The following step is to drain the h2o from the aquarium. If you do not have a floor drain beneath the valve, you can join a hose to the drain valve, close the foundation of the aquarium. Run it to a nearby drain or outdoors, and then open the valve.
- Unscrew the inlt and outlet fittings from the leading of the tank, using two wrenches.
- If you have a fuel drinking water heater, turn away the fuel inlt valve. Disconnect the union or flare fitting between the fuel offer pipe and the inlt valve. You can use two wrenches to disconnect the exact same. You will also discover a flue hat at the leading of the tank. It expels gases into the flue. Get rid of this flue hat as properly.
- Eliminate the previous h2o heater tank.
- Set the new h2o heater tank cautiously in spot so that the burner and controls are accessible. Make certain that there is at least six inches of clearance approximately its perimeter, and it is away from any flammable supplies.
- It is better if you fill the base with pieces of asphalt shingles or plastic wedges.
- Wrap the threads of the warmth entice fittings with pipe-wrap tape.
- Connect blue thread of the fittings into the chilly h2o inlt of the h2o heater tank, and red into the sizzling h2o outlet.
- Be careful while connecting the exact same. Make positive that the arrows are marked on the fittings level in the drinking water movement direction.
- On the inlt and outlet pipes of drinking water tank install the new versatile connectors.
- Make positive that all connections are complete.
- Open the shutoff wall and fill the fish tank.
- Open a couple of sizzling-h2o faucets so that the air in the pipes ought to bleed away.
- Now assemble the fuel pipes per the manufacturer's instruction.
- Brush soapy h2o on all the connections, and cautiously view it ought to not create any bubbles. If it does, recheck the connection as soon as once again.
Some Other Helpful Suggestions
- Check with your local constructing department and verify regardless of whether your house is in an earthquake zone. Set up straps approximately the new drinking water tank.
- If the peak of the new tank is distinct from the outdated 1, you will have to use versatile pipe connectors for the drinking water inlt and outlet. This will make them in a position to bend whenever it is required to make the hookup.
In case the pipes are not threaded, change them with threaded nipples. Use an adjustable wrench to modify the connectors to the nipples.
Therefore, if you adhere to the over measures and the tips, you will discover it very easy to change a drinking water heater.
About the Author:
The expert company of Albuquerque Plumbing provides plumbing quotes and every residential plumbing service you may need, from fixing various toilet plumbing dilemmas, sewage systems and pipelines in case of running water problems, to setting up boilers in your shower for your leisure.
No comments:
Post a Comment